NEW! Owatrol Oil is now available in a handy and easy-to-use 300ml spray can. Making it even easier to apply, especially to those hard to reach places!
Owatrol Oil is versatile, highly penetrating air drying oil that can be used alone or added to paint. Used alone as a rust inhibitor it provides a tough, flexible finish, driving out excess moisture and air; displacing it from rusted metal, so stopping rust dead in its tracks. Used alone on porous wood surfaces it will saturate and protect the wood from damage caused by moisture and prevent paint from peeling.
When added as a paint conditioner to any oil or alkyd based coatings it will give increased wet edge time, improved flow and greater adhesion. Unlike damaging thinners, it will maintain the inherent quality of the paint without affecting its appearance or drying times, allowing you to achieve a more professional finish.
Using Owatrol Oil as a rust inhibitor
Owatrol Oil penetrates through the rusted metal to the sound metal below, isolating it and protecting it from further rusting. Directly use on rusted surfaced – the penetrating oil drives out moisture and air and stabilises the metal to protect it from future damage.
On brand new metal surfaces, use Owatrol’s AP 60 instead. If you are looking for a high gloss rusted finish you can also overcoat the surface with Deks Olje D2 high gloss clear oil.
Using Owatrol Oil to aid adhesion
A bonding film is left on all surfaces Owatrol Oil is used on which maintains the natural look of the surface but allows enhanced adhesion, making it perfect as a foundation for primers or finishing coats. It gives excellent adhesion including on galvanised steel, aluminium, zinc, wood and more. Paint can be applied directly to firm rust when Owatrol Oil is used and is heat resistant up to +175°C.
Using Owatrol Oil as a paint conditioner
Mix Owatrol Oil into oil-based paints as a paint conditioner to get several great benefits. Firstly, it gives the paint rust inhibiting properties and helps prevent rust on painted surfaces (even when rust is already present). Secondly, it also improves the flow and workability of the paint. This means that you can maintain the ‘wet edge’ for longer, reducing brush and roller marks. Finally, it gives the paint a better viscosity allowing painting work to be carried out in a more extreme cold, hot and windy conditions. Unlike damaging paint thinners it does all this without altering the inherent qualities or the finish of the paint.
Please note that if you are looking for a product to give this effect but for water-based paints then please use Floetrol instead as it is designed for use in any water-based paint whereas Owatrol Oil is for use in oil-based paints.
Using Owatrol Oil for wood impregnation
When used on wood surfaces Owatrol Oil saturates the wood and protects it from damage caused by moisture. It also helps to prevent paint from peeling and protects metal parts such as hinges and latches from corrosion.
Ideal Uses for Owatrol Oil
- Priming galvanised surfaces with no need for weathering or pickling
- Preventing further damage in heavily rusted surfaces
- Improving paint flow when working in cold environments
- Preventing peeling paint on wood surfaces
- Protecting metal part on wood surfaces like gates and window frames
- Assuring better adhesion of finishes
Application tools
- Brush
- Roller
- Airless or HVLP sprayer
- Garden sprayer, pump sprayer
Surface Preparation
Surface preparation when using Owatrol Oil as a rust inhibitor
First, surfaces must be clean, dry and free from oil, grease and other surface contaminants. Remove all scale; loose and flaking rust and old paint back to a sound surface and edge and feather in any sharp edges. Surfaces exposed to chemicals (acids, alkalis or salt deposits) should be washed using copious amounts of water or steam cleaned. Severely contaminated surfaces should be cleaned using an appropriate solvent.
Do not remove firm rust or clean the metal back to a bright finish.
Surface preparation when using Owatrol Oil as a paint conditioner
First prepare the surface as per the instructions on your paint can. In addition, if not asked to ensure that you remove all loose and flaking material and treat any organic growth with fungicidal solution or a mix of 1 part water to 1 part chlorine bleach (allow bleach solution to sit for 15 minutes), rinse thoroughly and allow to dry.
Applying Owatrol Oil as a Rust Inhibitor
Using Owatrol Oil on new clean steel
First prime new steel with a mix of 1 part Owatrol Oil to 3 parts primer. Then follow with normal paint system adding Owatrol Oil to subsequent coats as directed under ‘Mixing instructions’ below.
Using Owatrol Oil on lightly rusted surfaces
First prime the surface with a mix of 1 part Owatrol Oil to 2 parts primer. Then follow with normal paint system adding Owatrol Oil to subsequent coats as directed under ‘Mixing instructions’ below.
Using Owatrol Oil on new unpainted rusty steel
First prime the surface with a mix of 1 part Owatrol Oil to 1 part Primer. Then follow with normal paint system adding Owatrol Oil to subsequent coats as directed under ‘Mixing instructions’ below.
Using Owatrol Oil on old, severely rusted or previously coated surfaces
first apply wet on wet applications of Owatrol Oil to all exposed rust until fully saturated and allow it to dry. Saturation is indicated by a uniform glossy appearance to the surface when Owatrol Oil is dry. Before Owatrol Oil has hardened, check the surfaces and remove rust scale and old paint loosened by the above. If needed, touch up these areas. Allow to dry. Next apply a mix of 1 part Owatrol Oil to 2 parts primer and allow to dry. Then follow with normal paint system adding Owatrol Oil to subsequent coats as directed under ‘Mixing instructions’ below.
Note: Owatrol Oil will not lift well bonded paint.
Applying Owatrol Oil as a Paint Conditioner
First apply paint in normal the manner. If the paint is sticky, drags, sets up to fast or does not level properly add Owatrol Oil (stirring in well) until the paint works smoothly, easily and evenly. Allow the brush, roller or sprayer to be your guide.
Using Owatrol Oil as a Paint Conditioner for wood surfaces in sound condition
First prime any bare wood with a mix of 1 part Owatrol Oil to 2 parts primer and allow to dry. Follow with normal paint system adding Owatrol Oil as in ‘Mixing Instructions’ below.
Using Owatrol Oil as a Paint Conditioner on damaged, soft or punky wood surfaces
First apply 2 to 4 liberal applications of Owatrol Oil wet on wet, as fast as the wood will absorb it. Do not allow Owatrol Oil to dry between applications. When the wood cannot absorb any more wipe up any excess and allow to dry overnight (12 hrs). Follow with normal paint system adding Owatrol Oil as in ‘Mixing Instructions’ below to ease application and aid adhesion.
Mixing instructions
Topcoat: As required – normally 5 %-20 % by volume.
Undercoat: up to 30 % by volume.
Primer: up to 50 % by volume.
The above is meant as a guide only. Conditions of application, porosity of surface etc. will dictate the amount of Owatrol Oil to be mixed into the paint.
Clean Up
Clean all tools and equipment with white spirits while still wet. If allowed to dry, remove with paint stripper. Store and maintain equipment as directed by manufacturer.
NOTE: Any rags, steel wool etc soaked in Owatrol Oil may spontaneously catch fire if improperly discarded. Rags, steel wool etc must be saturated with water after use or placed in a sealed, water filled metal container, before disposing with household waste.
Restrictions
Do not mix or overcoat Owatrol Oil with paints containing hot solvents i.e. Xylene, 2 part coatings, chlorinated rubber etc. – for these type of paints use Owatrol CIP instead. Do not use Owatrol Oil as a paint conditioner in water-based paints, for this purpose use Floetrol instead – Owatrol’s water-based paint conditioner.
Things to Remember
- Cover everything you do not wish to paint.
- Apply between + 5°C and + 35°C.
- Do not apply in direct sunlight or on to hot surfaces.
- Test for compatibility when adding Owatrol Oil to paint.
Leslie Kay –
Verified Owner
If you have a good smooth surface below you’ll get a superb professional looking job using Owatrol.
Scott Lambert –
If there was one product we were itching to get our hands on, it was this! We’d heard so many good things about Owatrol Oil that we wanted to see if the hype was deserved. It¹s worth explaining that there are several strings to this product’s bow. It can be used as a rust inhibitor, paint conditioner or for impregnating wood, but we used it as instructed by our readers in a bid to enhance the look of an original tractor. Owatrol Oil allows you to achieve that’oily rag’ look, without the mess, while stopping rust and protecting the base metal from further rusting, eliminating moisture and penetrating down to the sound metal. We cleaned up the tinwork of our tractor before applying Owatrol Oil with a clean rag and achieved some excellent results. Yes, it’s expensive, but you don¹t need that much to achieve the desired effect, so it should last a while.
Nick –
This is brilliant at stabalising rust inside van/car sills chassis and bodywork. It is the only product I’ve ever tried that actually genuinly stops existing rust in vehichles from getting any worse. I live on a farm in the west coat of Scotland, which is wet/mud all year round and salty all winter. It is a climate that kills cars as they never get a chance to dry out.
I’m lazy, and prefer the effort of prevention than the effort of welding. I bought 5 litres of this oil to treat the rusty chassis and sills on my van, in preference to the vareous waxes that I’ve used (Dynax S50, Noxudol-700, Waxoil) . My van is an already rusty daily driver, and I was seeking a product to stabalise the existing rust, and prevent any more from forming, whilst at the same time not hindering any future welding that might be needed.
I’ve found most products aimed at cars don’t solve existing rust, they expect clean metal, and even the rust converters are only converting the top surface of rust that is there. Even the best waxes I’ve trialed simply don’t soak that far into the rust, and in my experience allow the rust to carry on doing its thing underneath them.
It took about 3 litres to fully coat all my chassis rails and sills, and to paint over all bare metal on the underside of my van. I did two coats on the exterior metal, and one on the sills. Areas vulnerable to stone chips were top coated with Dynax S50 (which is meant for sills but I suddenly have a lot of this that I don’t need so its been re-purposed.)
I’ve also done some test pieces of rusty box section so I can have a side by side comparison with the waxes I use, and so I can test how slap dash I can get away with being on surface preperation.
Below are the reasons why I think its brilliant, and what I’ve found as the negatives of it.
1) It really really penetrates, and will genuinly soak through existing scale rust to reach the metal underneath. It soaked through all my van body seams, and completly saturated the rust already deep in those seams. I have been able to paint areas that I have no other way of ever reaching. It seems to penetrate to a similar level as WD40, but with the advantage that it dries afterwards.
2) It dries clear (surface looks like its wet), so I am able to confirm that the rust underneath the coating is stable.
3) The oil actually dries, as compared to cavity waxes which generally don’t. This is a significant advantage to me as it allows me to do welding repairs without setting the inside of the sills on fire, or contaminating welds with wax. There speaks the voice of experience.
4) It smells pleasent, and is not sticky whilst applying it, and is easy to wash off, and clean up afterwards.
5) Its fine with dirty/rusty base metal, which is the underside reality of a van. This makes preperation really easy, essentially a once over with a pressure washer, and a once over with a needle scaler. A wire brush would be OK, but the needle scaler is faster and better with some of the heavy scale that was on my van.
BUT, its not all good.
6) Its slow to dry, making it difficult to get two coats on in a weekend, when you need your vehicle on both Friday and Monday.
7) It needs the metal to be dry, it won’t displace water that is already there. When I did the whole van I had a week of sun prior to coating. For winter spot treatment I use a hot air gun to get rid of water, if needed.
8) Its so effective at penetrating that a lot of what went into the sills soaked through the seams and coated my garage floor.
9) Because its clear it is very hard to tell how effectivly it has coated the sills as I can’t tell what has and hasn’t been covered when I inspect them with my borescope.
10) Its not very impact resistant, so is vulnerable to stone strikes sprayed up by my wheels. In vulnerable areas I’ve overcoated it with underseal to avoid this.
11) I’m 35 and never knew this stuff existed, I wish I’d discovered it decades ago, it would have saved me so much grief over the years. Seriously though its not something I can walk into a local shop and buy, but no worse than some of the other things I’ve thrown at my van over the years. I just wish it was more widely known, hence the review.
So, I’m a fan, probably a customer for life, and feel slightly lighter knowing that all the rusty junk I love to acumulate won’t rot to nothing now.
George Shearer –
Verified Owner
I have applied the oil to a totally unrestored walk behind tractor it applied well. will update at later date
Terry –
Verified Owner
Wouldn’t dream of doing any painting on our canal boat without using Owatrol, especially good patching damaged areas .
Brilliant product, does exactly what it says on the tin.
Richard Baker –
I felt compelled to write and tell you about my experience with the Owatrol products I used when painting my dining room. To give you some background, I hate glossing with such a passion that with my previous houses I removed all skirting boards and doors and architraves, replacing them with natural wood. However recently we have moved into an old cottage and removing these items would not have been in-keeping with the structure of the cottage.
Searching on the internet I people recommending Owatrol Oil and ESP, products I have never heard of before. After searching out the company on the web and phoning your help-line to find a local distributor I purchased both products. Unbelievable!!! The outcome is amazing. I have always wanted gloss that resembles the finish on car body work…well now I have found the product that delivers such a finish. Just a few words of gratitude from a new life long customer of the Owatrol products.
Paint It Now –
I used Owatrol Oil on some rusty railings the other week and the result is great! Now I’m just waiting for some dry weather to paint them…
Lees Decor –
Your paint conditioner Owatrol Oil is superb! It’s a bit difficult to get out of the tin but a big thumbs up from me!